NOTE: These units are custom-made, based on the model generator you have. A lead-time of 14-21 days is required from the time you place your order. Please state which model generator you have in the comments section during your checkout as there are small customizations that must be made for final manufacture. The MEP002A-MEP003A Auto-Remote Starter Kit is a great add-on for your MEP military diesel generator set. It will allow remote start with the flip off a switch or it can be connected to an Automatic Transfer Switch (ATS) for automatic starts.
- Our Auto / Remote Start Kits have been available since the end of 2013.
- We cover all MEP makes and models.
- Highly Reliable Systems in operation with Military, Fire and Police Departments who depend on 100% reliable operations and up time.
- Self Contained Unit which prevents restart in case of generator error / failure to prevent further damage by restart attempts.
- Wide Operating Range: -55C to 80C / 100% Humidity.
- Highest Quality Components.
- Unsurpassed in reliability, quality and ruggedness.
- Meets and exceeds MIL-STD.
- Each Kit is custom assembled, programmed and conformal coated when purchased to increase shelf life.
- Our PCB’s are gold plated and made in the USA in Illinois.
- If you want the best, then this is your system.
The MEP002A-MEP003A auto-remote starter kit has the following features which can be set with the DIP switch on the board:
- DIP Switch 1: Choose day-tank fuel mode or auxiliary fuel tank mode (Note: the auxiliary fuel source fills the day-tank and the day-tank feeds the engine.)
- DIP Switch 2: Warm up Time 1 min or 5 min (This is the time delay before the Relay “Power On” is activated. This Relay switches the Control Voltage to the 3 Phase Contactor “On” and connect the LOAD to the Generator)
- DIP Switch 3: Cool Down 2 min, 6 min or 10 min (This is the time delay after the Relay “Power On” is disengaged, shutting off the Control Voltage to the 3 Phase Contactor removing the LOAD from the Generator and therefor allowing the unit to cool down)
- DIP Switch 4: Pre-heat Time determined by ambient air temperature or fixed time (See table below)
- DIP Switch 5: Pre-heat Time 15 sec or 45 sec [if DIP Switch 4 is set to fixed time] ( This setting is for the case that the Generator is operated in a controlled environment i.e. Building, Garage etc)
The auto-remote kit will automatically shut down and display a light indicator in the event of a Oil Pressure or Overheat situation, preventing the generator set from automatically restarting. The auto-remote kit can easily be reset, once the issues leading to the low oil pressure or overheat situation have been remedied.
The installation is not difficult for the do-it-yourself-er. GMG can also install the basic kit if you purchase your generator from GMG.
The MEP002A-MEP003A Autostarter KIT includes:
- MEP 002A/003A Autostarter Circuit Board
- MIL-I-46058C Conformal Coating
- Drill / Mounting Templates
- Detailed Installation Manual
- 24 feet 16ga standard multi stranded SXL wire, strong resistance to moisture, solvents and prolonged high heat – Thick wall special purpose automotive wire is insulated with chemically cross-linked polyethylene. Withstands prolonged temperatures of up to 257°F
- Mounting Hardware [Stainless Steel Phillips Pan Head Machine Screws #6-32×0.75″, Stainless Steel #6-32 Nuts as Spacers, Stainless Steel #6-32 K-Lock Nut’s
- Crimp On Fork and Ring Lugs
- Wiring Diagram
- 1 Year Limited Warranty
Not included in this KIT (You can purchase these items separately or you may have them already. We have recommended the above items in the manual with manufacturer part numbers.):
- 65 Amp 3 Phase Contactor
- 4 Pole Receptacle
- 4 Pole Connector with 16 gauge wire